Home » News » PPSU Vs Tritan

PPSU Vs Tritan

Views: 0     Author: Rio Liang     Publish Time: 2026-11-19      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button
PPSU Vs Tritan

PPSU vs Tritan: Heat Resistance, Strength, Chemical Resistance, Price & Sterilization Compared

Last updated: 19 November 2026 |  Data source: BASF P3010 TDS.pdfand Eastman Tritan™ TX1001 TDS |  Reading time: about 11 minutes


Short answer: PPSU Material is a high-temperature polyphenylsulfone that survives repeated steam    sterilization, while Tritan is a clear, BPA-free copolyester built for everyday food-contact parts.    Choose PPSU when the part must be boiled or autoclaved repeatedly; choose Tritan when transparency,    low weight and cost matter more than heat ceilings.

These two materials are compared constantly in baby bottles, sports bottles, small appliances and reusable  medical devices, yet they are not direct competitors. PPSU is a polymer family; Tritan is a trademarked  copolyester. This comparison puts the leading grade of each against the other using published supplier  data, so the numbers can be checked line by line.


Quick comparison: PPSU vs Tritan

  • Heat: PPSU deflects at 197 °C under 1.8 MPa; Tritan deflects at 85 °C, a 2.3× gap.

  • Stiffness: PPSU is about 45 % stiffer (2,250 MPa vs 1,550 MPa tensile modulus).

  • Transparency: Tritan transmits 90 % of light with haze below 1 %; PPSU is amber-translucent by nature.

  • Sterilization: PPSU handles superheated steam and autoclave cycles; Tritan is designed for dishwasher exposure, not autoclaving.

  • Price: PPSU resin typically costs 2.5 to 4 times more than Tritan copolyester.

  • Safety: Both are BPA-free and food-contact compliant. The real risk is using either outside its temperature window.


Quick decision table: which material for which application

Match the requirement to the material before reading the detailed data.

Application-first selection guide
If your requirement is Choose Why
Baby bottles boiled or steam-sterilized daily PPSU Superheated-steam resistance; no deformation across repeated cycles
Sports bottles, toddler cups, everyday drinking Tritan 90 % light transmission, low weight, roughly half the resin cost
Coffee-machine boilers, hot-water valves PPSU 197 °C HDT and long-term service near 170–180 °C
Reusable medical instruments, autoclave trays PPSU Survives 121–134 °C saturated steam
Clear cosmetic jars, display containers, blender jugs Tritan Glass-like clarity with haze under 1 %
Strong alkalis, solvents, aggressive disinfectants PPSU Sulfone chemistry outclasses copolyester across the board
Precision parts under combined heat, moisture and load PPSU Minimal creep; balanced 0.9–1.0 % shrinkage

Side-by-side specification comparison

The table below uses values exactly as published in the two datasheets. Where a property is not stated by  the supplier, it is marked as such rather than estimated.

PPSU (BASF Ultrason P3010) vs Tritan (Eastman TX1001)
Property PPSU — P3010 Tritan — TX1001
Polymer class Polyphenylsulfone (PPSU) Amorphous copolyester (PCTG)
Density 1.285 g/cm3 1.18 g/cm3
Glass transition temperature (Tg) 220 °C (DSC) Not stated in TDS; PCTG class is far lower
Heat deflection temperature, 1.8 MPa 197 °C 85 °C
Heat deflection temperature, 0.45 MPa Not stated 99 °C
Tensile modulus 2,250 MPa 1,550 MPa
Tensile stress at yield 74 MPa 43 MPa
Elongation at break Not stated 210 % (ASTM D638) / 190 % (ISO 527-2)
Notched Izod impact, 23 °C 58 kJ/m2(ISO 180/A) 93 kJ/m2; (ISO 180) / 980 J/m (ASTM D256)
Notched Charpy impact, 23 °C 70 kJ/m2 Not stated
Notched impact at low temperature 50 kJ/m2; at -30 °C (Charpy) 20 kJ/m2; at -40 °C (Izod, ISO 180)
Hardness Ball indentation 124 MPa Rockwell R112
Light transmission Amber-translucent 90 %, haze below 1 %
Flammability UL 94 V-0 at 1.5 mm and 3.0 mm Not a rated property
Molding shrinkage 0.90 % parallel / 1.00 % normal 0.50–0.70 % machine direction
Water absorption at saturation 1.2 % Low (not stated)
Coefficient of linear thermal expansion 55 × 10-6 /K (23–80 °C) Not stated; higher than PPSU
Melt temperature, injection molding 350–390 °C 260–282 °C
Mold temperature 140–180 °C 38–66 °C
Predrying before processing 130–150 °C for at least 4 h 88 °C for 4–6 h
Indicative resin price, 2026 About 70–220 per kg depending on origin About 45–75 per kg

1. What PPSU and Tritan actually are?

PPSU is a polymer family; Tritan is a brand name. The two belong to different material classes and  are only compared because their end uses overlap.

PPSU stands for polyphenylsulfone, a member of the sulfone family alongside polysulfone (PSU) and  polyethersulfone (PES). It is an amorphous engineering thermoplastic that is naturally amber-tinted because  of its molecular structure. Grades such as BASF Ultrason P3010 are unreinforced, medium-viscosity products  for injection molding and extrusion, formulated for toughness, stress-crack resistance and resistance to  superheated steam.

Tritan is Eastman Chemical's trademark for a family of amorphous copolyesters, often classified as PCTG.  Grade TX1001 is an injection-molding copolyester that includes a vegetable-derived mold release. Its  headline properties are clarity, toughness, hydrolytic stability and durability in dishwasher environments.

Reframe the comparison: Tritan's real substitute in the market is polycarbonate, a clear,impact-resistant material that raised BPA concerns. PPSU's true peers are PSU and PES. Pitting PPSU against Tritan means comparing a high-temperature sterilization platform with a clarity-first everyday platform.


2. Thermal properties: the widest gap between the two

PPSU deflects at 197 °C under 1.8 MPa load, more than twice Tritan's 85 °C, and this single  difference explains most of the application split between them.

Thermal metric PPSU P3010 Tritan TX1001
Glass transition temperature 220 °C Not published; substantially lower
HDT at 1.8 MPa 197 °C 85 °C
HDT at 0.45 MPa Not published 99 °C
Typical long-term service ceiling 170–180 °C Around 100 °C in food-contact use
Melt processing window 350–390 °C 260–282 °C

The distinction that matters in practice: Tritan's 99 °C deflection at low load means a cup will not  collapse when filled with boiling water. It does not mean the part can live at that temperature. PPSU's  197 °C figure describes a continuous load-bearing capability, which is why it appears in boiler components  and autoclavable hardware.


3. Mechanical properties: stiffness versus ductility

PPSU delivers higher stiffness and stable low-temperature toughness, while Tritan delivers much  greater elongation and excellent room-temperature impact, but loses impact strength quickly as temperature  falls.

At 23 °C, Tritan's notched Izod value of 93 kJ/m2; actually exceeds PPSU's 58 kJ/m2;, and its  elongation at break of 210 % is far beyond anything a sulfone will reach. That combination makes Tritan an  outstanding drop-resistant material for thin-walled consumer goods.

The picture changes at low temperature. Tritan's notched impact falls to 20 kJ/m2; at -40 °C, while  PPSU holds 50 kJ/m2; at -30 °C. PPSU also carries roughly 45 % more tensile modulus and 72 % more  yield stress, so it resists deformation under sustained load in a way a copolyester cannot.

Read the two datasheets carefully: they report impact using different methods, PPSU in ISO 180 and ISO 179  units, Tritan in both ASTM D256 and ISO 180. Only the ISO 180 values are directly comparable, and even then  specimen geometry differs between suppliers.


4. Chemical resistance

PPSU resists strong alkalis, solvents and repeated hot-water exposure that would attack Tritan,  making sulfone the safer choice wherever cleaning chemicals or aggressive media are involved.

Chemical environment PPSU Tritan
Dilute acids and bases Resistant Resistant
Strong alkalis Resistant Not recommended
Alcohols Resistant Resistant
Fats, oils, detergents Resistant Resistant
Ketones and aromatic hydrocarbons Partly resistant Not recommended
Long-term hot-water immersion Hydrolytically stable Slow aging above about 80 °C
Superheated steam Resistant Not rated

Tritan's hydrolytic stability is genuinely good for a copolyester. The TX1001 datasheet explicitly targets  the combination of heat, humidity and aggressive detergents found in a dishwasher. What it does not claim  is autoclave-grade steam resistance, and prolonged exposure above roughly 80 °C in water tends to produce  haze and micro-cracking over time.


5. Sterilization and disinfection: the decisive difference

PPSU is engineered for superheated steam and repeated autoclave cycles; Tritan is engineered for  dishwashers and is not intended for pressurized steam sterilization.

Method PPSU Tritan
Boiling water, 100 °C Repeatedly Occasional; repeated boiling degrades appearance
Saturated steam, 121–134 °C Repeated cycles Not supported
Microwave steam sterilization Suitable Suitable with temperature control
UV sterilizer cabinet Suitable Suitable; gradual yellowing under long UV exposure
Dishwasher, normal cycle Suitable A design target of the grade
Medical autoclave Standard use Not applicable

On cycle counts, be precise about the source. The P3010 datasheet states resistance to superheated steam  but does not publish a cycle number. Suppliers of PPSU grades commonly cite figures in the range of 1,000  steam sterilization cycles at 132–134 °C with retained toughness. Treat such figures as supplier test data  for that specific grade, not as a generic PPSU guarantee.

Practical rule: Tritan is not unsafe to disinfect. It simply has a temperature ceiling.Steam above 100 °C is outside its design window; boiling water is a short-term contact, not a service    condition.


6. Dimensional stability

PPSU holds dimensions far better under combined heat, moisture and load, which is why it is chosen  for precision and load-bearing parts while Tritan is chosen for appearance parts.

Factor PPSU Tritan
Molding shrinkage 0.90 % parallel, 1.00 % normal, near-isotropic 0.50–0.70 % machine direction
Water absorption, saturated 1.2 % Low, not published
Water absorption, 23 °C / 50 % RH 0.6 % Low, not published
Thermal expansion, 23–80 °C 55 × 10-6 /K Higher than PPSU
Creep under load above 100 °C Minimal Significant
Drying before processing 130–150 °C, minimum 4 h 88 °C, 4–6 h

The near-balanced shrinkage of PPSU is a real manufacturing advantage for parts that must stay round or  flat. The trade-off is that PPSU pellets absorb moisture very rapidly. The datasheet is explicit that  pellets must be dried at 130–150 °C for at least four hours before processing. Skipping or shortening this  step is the most common cause of silver streaks, bubbles and strength loss in PPSU molding.


7. Operating environment

PPSU covers roughly -40 °C to 180 °C in continuous service with steam, chemicals and UV in  play; Tritan covers -40 °C to about 100 °C and is best kept to ambient and warm conditions.

For Tritan, the most common real-world failure mode is not impact or chemical attack, it is thermal. A  bottle left in a pot of boiling water, a cup run through a high-temperature steam sterilizer, or a  container repeatedly microwaved with a dry load will deform, cloud or yellow well before it breaks.


8. Where each material is used

PPSU dominates applications that must survive heat and repeated sterilization; Tritan dominates  applications where clarity, weight and cost drive the decision.

Typical PPSU applications

  • Baby bottles and drinking cups used with daily boiling or steam sterilization

  • Reusable medical instruments, dental trays, sterilization cassettes

  • Coffee-machine boiler parts, hot-water valves, filter housings

  • Laboratory ware and autoclavable containers

  • Aircraft interior components and high-temperature electrical insulation

  • Parts requiring a UL 94 V-0 flame rating at 1.5 mm

Typical Tritan applications

  • Sports bottles, toddler cups, shaker and blender jugs

  • Food storage containers and dry-goods canisters

  • Clear appliance housings, water tanks, cosmetic jars

  • Baby products used in low-frequency or non-steam cleaning routines

  • Transparent retail display packaging


9. Food-contact safety and compliance

Both materials are BPA-free and suitable for food contact; the meaningful safety question is  whether the part stays inside its declared temperature window.

Tritan TX1001 is documented in its own datasheet as suitable for repeated-use food-contact articles under  US FDA regulations. It also carries NSF/ANSI Standard 51 certification for food equipment materials and  NSF/ANSI Standard 61 certification for drinking-water system components, the latter being a genuinely  differentiating credential for water-contact parts.

PPSU grades are widely used in food-contact and medical applications, and many carry FDA, EU 10/2011 and  USP Class VI documentation. The P3010 datasheet reviewed here does not itself list FDA clauses, so for any  regulated project the compliance statement must be requested per grade and per production site rather than  assumed from the polymer type.

Note on bisphenols: Both PPSU and Tritan are marketed as BPA-free, and neither releases bisphenol A under normal use. Bisphenol S has been added to the REACH candidate list of substances of very high concern, so buyers exporting to the EU should request an explicit written declaration covering BPA, BPS and BPF, not just BPA.


10. Price comparison

PPSU resin costs roughly 2.5 to 4 times more than Tritan copolyester, and the gap widens in  finished goods because PPSU also molds at higher temperature with tighter process windows.

Material Origin Indicative price, 2026
PPSU Domestic Chinese producers about 11–15 USD per kg
PPSU BASF Ultrason, Solvay Radel about 17–36 USD per kg, medical grades higher
Tritan Eastman TX / MX / FX / EX series about 6.4–11 USD per kg
"Tritan-type" copolyester Unbranded PCTG about 4.2–7.4 USD per kg

These ranges are indicative market pricing, not datasheet values, and move with order volume, grade and  exchange rates. On a finished-product basis the gap is partly offset by PPSU's narrower processing window,  higher energy consumption and lower molding yield.


11. How to choose: a three-question framework

Ask about sterilization first, clarity second, and load plus chemistry third. The first yes decides  the material.

  1. Must the part be boiled or steam-sterilized repeatedly?    If yes, specify PPSU. There is no copolyester substitute.

  2. Is high clarity, low weight or cost the priority?    If yes, specify Tritan, provided the temperature ceiling is respected.

  3. Does the part carry sustained load, sit in aggressive chemistry, or require tight dimensional    control?    If yes, specify PPSU. If not, Tritan or polypropylene at lower cost will usually do the job.


12. Procurement checklist

Specify the grade, not the material name, and demand traceable documentation. Counterfeit and  blended material is the single largest risk in both supply chains.

Buying PPSU

  • Source from traceable grades: Solvay Radel, BASF Ultrason, or established domestic producers

  • Guard against regrind blending, which is visually hard to detect; request a certificate of analysis per lot

  • Collect: supplier TDS, FDA 21 CFR statement, EU 10/2011 declaration, food-contact conformity statement

Buying Tritan

  • Confirm an Eastman-authorized grade; unbranded "Tritan-type" PCTG is widespread

  • Collect: supplier TDS, brand authorization, written declaration on BPA, BPS and BPF

  • Verify the declared maximum use temperature against your actual cleaning routine

Also verify on the finished product

  • Gasket and seal materials, silicone or TPE grade

  • Printing inks and surface coatings

  • Assembly adhesives

  • Whether every wetted component meets the same food-contact standard as the body


Frequently asked questions

Which is better for baby bottles, PPSU or Tritan?

It depends on how often you sterilize. For daily boiling or steam sterilization, PPSU is the correct choice  because it withstands superheated steam without deformation. If you sterilize occasionally and value  transparency and lower cost, Tritan is a reasonable option, but it should not go into a steam sterilizer  rated above 100 °C.

Can Tritan hold boiling water?

Yes, briefly. Tritan TX1001 has a heat deflection temperature of 99 °C at 0.45 MPa, so a short pour of  boiling water will not collapse the part. What it cannot tolerate is prolonged contact with boiling water  or repeated steam exposure, which causes deformation, clouding and yellowing over time.

Is PPSU or Tritan more impact resistant?

At room temperature Tritan is excellent. Its notched Izod impact of 93 kJ/m2; on ISO 180 actually  exceeds PPSU's 58 kJ/m2;. But Tritan's impact strength drops to 20 kJ/m2; at -40 °C, while PPSU  retains 50 kJ/m2; at -30 °C. PPSU is also roughly 45 % stiffer, so it resists sustained load far  better.

Why is PPSU amber while Tritan is clear?

The color comes from the polymer backbone. The sulfone linkage in PPSU produces an inherent amber tint that  cannot be fully removed, giving roughly 70–85 % light transmission in thin walls. Tritan copolyester  transmits 90 % of light with haze below 1 %, which is why it reads as glass-like.

Do PPSU and Tritan contain BPA?

Neither material releases bisphenol A under normal conditions of use, and both are marketed as BPA-free.  PPSU is built from bisphenol-type monomers but the finished polymer contains no residual BPA at relevant  levels. Tritan is manufactured without BPA. For regulated markets, request a written declaration that also  covers BPS and BPF.

Which one is more expensive?

PPSU is significantly more expensive. Resin pricing sits around 11–15 USD per kg for PPSU depending on origin,  against about 4.2–7.4USD per kg for Tritan, a factor of 2.5 to 4. In finished goods the difference usually  widens to 3–5 times because of processing cost.

Can Tritan go in the dishwasher?

Yes. Dishwasher durability under heat, humidity and detergent attack is one of the design targets of the  TX1001 grade. A dishwasher cycle is not, however, a substitute for autoclave sterilization.

What is the hardest part of molding PPSU?

Drying. PPSU pellets absorb moisture very quickly and the datasheet requires 130–150 °C for at least four  hours before processing. Add a 350–390 °C melt temperature and a 140–180 °C mold temperature, and the  process window is narrow enough that equipment and tooling must be specified for it from the start.


Data sources

  • BASF Ultrason®P3010 NAT product technical datasheet, PPSU, 2026 edition

  • Eastman TritanTM TX1001 product technical datasheet, copolyester

  • UL Solutions yellow card data for Ultrason P3010

  • Market pricing ranges compiled from public industry quotations, indicative only

   All physical property values above are taken from the supplier datasheets named. Values vary with grade and test method. Confirm against the latest TDS and compliance documents from the supplier before final    specification.  

Rio Liang | High-Performance Plastics Expert
 
Email: rioplastic@foxmail.com   TEL/Whatsapp/Wechat: 008613421811533
 
20+ Years specializing in PEEK, PPSU, PES, PPS & PEI materil modification. Expert in resolving material properties and injection molding solutions. Open to technical discussions.

Related Articles

As a high-performance plastic supplier in China, PRES offers a range of high-performanceplastic products, including plastic pellets, plastic plates, plastic rods, plastic tubes, plastic powders, and high-performance 3D printing filaments.
Meanwhile, we provide mold design & manufacturing & injection molding services.

CONTACT US

Phone: +86 18676969309
Wechat:18676969309
Email: rioplastic@foxmail.com
WhatsApp: +86 18676969309
Add: No. 417, Chang Road, Changping Town, Dongguan City, Guangdong Province
KEEP IN TOUCH WITH US
Copyright © Dongguan PRES Plastic Raw Materials Co., Ltd. All Rights Reserved.